Klabbersack Posted February 2 Share Posted February 2 View File Water Features In-Game Water Tool - Place and remove water sources. Lakes, Streams, Rivers, and Seas. Optional Opt-out: Seasonal Streams - Flow rates vary with season, precipitation, and snow melt. Optional Opt-in: Waves and Tides - Sea level rises and falls. Dependencies Unified Icon Library BepInEx Detailed Descrption Water Sources: Stream - Constant or Variable Rate Water Source: Emits water depending on the settings for this mod. With Seasonal Streams disabled, the flow rate will be constant. With Seasonal Streams enabled the flow rate will vary with season, precipitation, and snowmelt depending on your settings. Left click to place within playable area. Hover over and right click to remove. River - Border River Water Source: Has a constant level and controls water flowing into or out of the border. While near the border, the source will snap to the border. Right click to designate the target elevation. Left click to place. Hover over and right click to remove. Lake - Constant Level Water Source: Fills quickly until it gets to the desired level and then maintains that level. If it has a target elevation below the ground level, it can drain water faster than evaporation. Right click to designate the target elevation. Left click to place within playable area. Hover over and right click to remove. Sea - Border Sea Water Source: Controls water flowing into or out of the border and the lowest sea controls sea level. With Waves and Tides disabled, it will maintain constant level. With Waves and Tides enabled the sea level rises and falls below the original sea level. Right click to designate the elevation. Left click to place if the radius touches a border. Hover over and right click to remove. Optional Opt-In Custom Water Sources: (Enabling/Disabling these in the settings requires restarting the game) Detention Basin: Custom modded water source that rises with precipitation and snowmelt and slowly drains when the weather is dry. They have a maximum water surface elevation but no minimum water surface elevation. Right click to designate the maximum elevation. Left click to place within playable area. Hover over and right click to remove. Retention Basin: Custom modded water source that rises with precipitation and snowmelt and slowly drains when the weather is dry. They have a maximum water surface elevation and a minimum water surface elevation. Right click to designate the maximum elevation. Left click to place within playable area. Hover over and right click to remove. The tool is accessed in the landscaping menu with a tab with a water drop and icons for the different water sources. Small radius water sources will have some extra clickable space for removing them. Large radius water sources will have a small filled circle for removing them. If you are placing a source with an assigned depth you should place them at the intended bottom of the water feature. For now you cannot remove water sources from utility structures. Seasonal Streams - Optional Opt-out Seasonal Streams takes Streams (Modified Constant Rate Water Source): and ties them to the climate and weather for the map. For example, if your map features a dry summer, then these water sources will decrease during the summer. Seasonal streams by it-self should not cause flooding since it treats the map's default water source amount as a maximum unless you change it. All aspects are optional and adjustable in the mod's settings. Waves and Tides - Optional Opt-in This feature is dependent on map design. Maps with a sea water source and a single shoreline work best. The point of the waves feature is to make the shore move in and out and make sand along the shoreline. A better way to make beaches is to just paint them with surface painter instead. Waves are generated at the map boundary where there is a Sea water source. Once generated they head towards shore. Maps were not necessarily designed for these waves, but the waves will always be lower than the sea level from the original map. Tides are the biggest waves and they cause the sea to rise and fall along the shore. Tides can add sandy graphics along shorelines but the sand may not persist the entire time between low tide and high tide. Option to change the global damping value. The setting is inverted though so higher numbers mean less damping and stronger waves. Maps such as San Francisco with shallow seas will need waves and tides with smaller heights to avoid large swathes of non-playable area becoming dry sand. Saving Before saving, the mod always resets all water sources including the custom ones in a manner that can be loaded safely without the mod, so that the mod can be removed at any time. Additional Features in the Settings Adjust the global evaporation rate which can be helpful with Detention and Retention basins. Water Clean Up Cycle is an emergency solution for removing water in developed areas by increasing the global evaporation rate for a short time. Better option: Lakes with an elevation below the ground surface drain water faster than evaporation. Submitter Klabbersack Submitted 02/02/2024 Category Cities: Skylines 2 - General Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.